======STS-1 Mission Checklist======
<note Important> **Checklists will look best at a screen resolution of 1280*1024 and above** \\ if you are using lower resolution you might see misaligned text **please** Do not try and "fix it" for the majority of users do use these screen resolution</note>



^  COMM  ^  MET  ^  Panel Section  ^  Panel  ^    procedure    ^  Panel Area & Notes  ^
^  1105  |  Mission depending  |  Center Panel \\ \\ \\ \\ Overhead AFT Panel \\ \\ \\ Center Panel  |  C2 \\ \\ \\ \\ C3 \\ O14 \\ O16 \\ C2  | * Enter [[ops2#ops202|OPS 202 PRO]] **(Right Keypad)** \\ * Enter ITEM 22 EXEC **(Right Keypad)** \\ * Confirm ORBITAL DAP/CONTROL Is set To AUTO \\ * Enter ITEM 27 EXEC **(Right Keypad)** \\ * Enter ITEM 23 EXEC **(Right Keypad)** \\ * Set OMS ENG (Left & Right) To ARM/PRESS \\ * Set L OMS ENG VLV To ON \\ * Set R OMS ENG VLV To ON \\ * Press EXEC - **(Right Keypad)** Confirms ready for OMS burn| ** only required if the CRT is not on ORBIT MNVR display** \\ Orbit Adjustment Burn - (First OMS Burn) \\ \\ \\ \\ \\ \\ Orbit Adjustment Burn - (Second OMS Burn)  |
^  1106  |  Mission depending  |  Center Panel  |  C3  | * Set OMS ENG (Left & Right) To OFF| First Orbit Adjustment Complete \\ Next Event  |
^  1110  |  Mission depending  |  Center Panel  |  C2 \\ \\ \\ C3 \\ C2  | * Enter ITEM 22 EXEC **(Right Keypad)** \\ * Enter ITEM 27 EXEC **(Right Keypad)** \\ * Enter ITEM 23 EXEC **(Right Keypad)** \\ * Set OMS ENG (Left & Right) To ARM/PRESS \\ * Press EXEC - **(Right Keypad)** Confirms ready for OMS burn| Note: ORBIT MNVR EXEC Should Be Displayed On The CRT. \\ \\ \\ \\ Note: LOAD Will Be Flashing On The CRT |
^  1111  |  Mission depending  |  Center Panel  |  C3  | * Set OMS ENG (Left & Right) To OFF| OMS Burn Complete  |
^  1112  |  Mission depending  |    |    |   | Columbia Continues Its Mission \\ Next Event  |
^  1115  |  Mission depending  |  Front Left Panel  |  F6  | * Confirm FLT CNTLR POWER Is ON| Shuttle Translation Test  |
^  | **Shuttle Translation Test** \\ \\ Translate the shuttle around as you wish. This is a great opportunity to see how the shuttle performs. \\ The orbital digital auto pilot (ORBITAL DAP) push buttons on the CENTER PANEL (C3), control the behavior of the Translation/Rotation actions.\\ In PULSE mode the RCS fires short burst each time the joystick is deflected. \\ In DISC RATE mode the RCS fires for as long as you deflect the joystick, the RCS will fire Counter-Bursts once the joystick is released until the shuttle stabilizes \\  The PRI, ALT and VERN modes select different dead bands size and rates of thrust. VERN mode uses dedicated RCS’s and is used for final attitude adjustments. \\ VERN mode conserves fuel and is the primary mode used while in orbit. \\ The LOW Z & HIGH Z translation modes select whether any up-firing jets are allowed to fire. \\ \\ \\   Once the translation tests are complete, Select NEXT EVENT and follow the Deorbit & Landing Checklist  |||||
\\
\\
^  [[STS-1|Back to STS-1]]  ^^
^Previous checklist:  |[[post-launch-checklist|Orbit Insertion Checklist]]  |
^Next checklist:  |[[deorb-checklist|De-orbit Checklist]]  |
^  [[missions|Go-To Missions Index]]  ^^