User Tools

Site Tools


deorb-checklist

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
deorb-checklist [2008/09/08 18:52]
uri_ba
deorb-checklist [2008/11/12 07:03] (current)
uri_ba added links to OPS2 and OPS3 pages
Line 5: Line 5:
 ^  1000  |  Mission Dep.  |  Left  |  L1  | * Set RAD CONTROLLER - OUT TEMP To HIGH  \\ * Set RAD CONTROLLER (LOOP 1 & LOOP 2) To OFF  \\ * Set RAD CONTROLLER - BYPASS MODE (1 & 2) To MAN  \\ * Confirm RAD FLOW BYPASS VALVE Talkbacks Display (BYP)  \\ * Confirm The HI LOAD EVAP ENABLE Is Set To OFF  \\ * Set FLASH EVAP CONTROLLER (PRI A & PRI B) To ON  \\ * Set FLASH EVAP CONTROLLER - SEC To ON  | Trap Cold Freon In The Bay Radiators If The Rad \\ Bypass Valve Talkbacks Do Not Display (BYP), \\ Set The Manual Rad Flow Bypass Switches 1 & 2 To Bypass. ​ | ^  1000  |  Mission Dep.  |  Left  |  L1  | * Set RAD CONTROLLER - OUT TEMP To HIGH  \\ * Set RAD CONTROLLER (LOOP 1 & LOOP 2) To OFF  \\ * Set RAD CONTROLLER - BYPASS MODE (1 & 2) To MAN  \\ * Confirm RAD FLOW BYPASS VALVE Talkbacks Display (BYP)  \\ * Confirm The HI LOAD EVAP ENABLE Is Set To OFF  \\ * Set FLASH EVAP CONTROLLER (PRI A & PRI B) To ON  \\ * Set FLASH EVAP CONTROLLER - SEC To ON  | Trap Cold Freon In The Bay Radiators If The Rad \\ Bypass Valve Talkbacks Do Not Display (BYP), \\ Set The Manual Rad Flow Bypass Switches 1 & 2 To Bypass. ​ |
 ^ ^^^^^^ ^ ^^^^^^
-^  1001  |  Mission Dep.  |  Right Aft  \\  \\  \\  Aft Left  \\  Right Aft  |  R11L  \\  \\  \\  A1U  \\  R13L  \\  \\ R11L  | * Confirm The MAJ FUNC Switch Is Set To GNC  \\ * Enter SPEC 33 PRO (**AFT Keypad**) ​ \\ * Enter ITEM 2 EXEC (**AFT Keypad**) ​ \\ * Set KU BAND POWER To OFF  \\ * Set KU Antenna To STOW  \\ * When Talkback Shows STO, Set KU Antenna To GND  \\ * Enter SPEC 22 PRO (**Aft Keypad**) ​ \\ * Enter ITEM 9 EXEC (**Aft Keypad**) ​ \\ * Enter ITEM 10 EXEC (**Aft Keypad**) ​ | Deactivate & Stow The KU Antenna ​ \\  \\  \\ If Rendezvous Navigation Has Been Used It Must Be Disabled. ​ \\ To Disable Enter: ITEM 1 EXEC On The AFT Keypad. ​ |+^  1001  |  Mission Dep.  |  Right Aft  \\  \\  \\  Aft Left  \\  Right Aft  |  R11L  \\  \\  \\  A1U  \\  R13L  \\  \\ R11L  | * Confirm The MAJ FUNC Switch Is Set To GNC  \\ * Enter [[ops2#​spec_33|SPEC 33 PRO]] (**AFT Keypad**) ​ \\ * Enter ITEM 2 EXEC (**AFT Keypad**) ​ \\ * Set KU BAND POWER To OFF  \\ * Set KU Antenna To STOW  \\ * When Talkback Shows STO, Set KU Antenna To GND  \\ * Enter [[ops2#​spec_22|SPEC 22 PRO]] (**Aft Keypad**) ​ \\ * Enter ITEM 9 EXEC (**Aft Keypad**) ​ \\ * Enter ITEM 10 EXEC (**Aft Keypad**) ​ | Deactivate & Stow The KU Antenna ​ \\  \\  \\ If Rendezvous Navigation Has Been Used It Must Be Disabled. ​ \\ To Disable Enter: ITEM 1 EXEC On The AFT Keypad. ​ |
 ^ ^^^^^^ ^ ^^^^^^
 ^  1002  |  Mission Dep.  |  Right Aft  |  R13L  | * Set PL BAY MECH PWR (SYS 1 & SYS 2) To ON  \\ * Set RADIATOR CONTROL (SYS A & SYS B) To STOW  \\ * Set LATCH CONTROL (SYS A & SYS B) To LATCH  \\ * Set LATCH CONTROL (SYS A & SYS B) To OFF \\ * Set RADIATOR CONTROL (SYS A & SYS B) To OFF \\ * Set PL BAY MECH PWR (SYS 1 & SYS 2) To OFF  | Stow The Radiators \\ Wait Until The RADIATOR CONTROL Talkbacks Show STO \\ Before Setting The LATCH CONTROLS SYS 1 & SYS 2 To LATCH. \\ Wait Until Latch Control Talkbacks Show LAT Before \\ Turning Off ALL Radiators. | ^  1002  |  Mission Dep.  |  Right Aft  |  R13L  | * Set PL BAY MECH PWR (SYS 1 & SYS 2) To ON  \\ * Set RADIATOR CONTROL (SYS A & SYS B) To STOW  \\ * Set LATCH CONTROL (SYS A & SYS B) To LATCH  \\ * Set LATCH CONTROL (SYS A & SYS B) To OFF \\ * Set RADIATOR CONTROL (SYS A & SYS B) To OFF \\ * Set PL BAY MECH PWR (SYS 1 & SYS 2) To OFF  | Stow The Radiators \\ Wait Until The RADIATOR CONTROL Talkbacks Show STO \\ Before Setting The LATCH CONTROLS SYS 1 & SYS 2 To LATCH. \\ Wait Until Latch Control Talkbacks Show LAT Before \\ Turning Off ALL Radiators. |
Line 13: Line 13:
 ^  1004  |  Mission Dep.  |  Overhead Aft \\ \\ \\ \\  Right Aft  |  O14 \\ O15 \\ O16  \\  \\  O15  \\  R11L  | * Set RGA 1 To ON \\ * Set RGA (2 & 4) To ON \\ * Set RGA 3 To ON  \\ * Set ACCEL 3 To ON  \\ * Set ACCEL 4 To ON  \\ * Set SUPPLY H2O - Crossover Valve To OPEN  | Gyro Assemblies & Accelerators ​ | ^  1004  |  Mission Dep.  |  Overhead Aft \\ \\ \\ \\  Right Aft  |  O14 \\ O15 \\ O16  \\  \\  O15  \\  R11L  | * Set RGA 1 To ON \\ * Set RGA (2 & 4) To ON \\ * Set RGA 3 To ON  \\ * Set ACCEL 3 To ON  \\ * Set ACCEL 4 To ON  \\ * Set SUPPLY H2O - Crossover Valve To OPEN  | Gyro Assemblies & Accelerators ​ |
 ^ ^^^^^^ ^ ^^^^^^
-^  1006  |  Mission Dep.  |  Right Aft  |  R11L \\ \\ \\ \\ R13L \\ \\ \\ \\ R11L  | * If Required, Enter OPS 202 PRO **(AFT Keypad)** \\ * Set MAJ FUNC Switch To SM \\ * Enter ITEM 1 EXEC **(AFT Keypad)** \\ * If Not Already Enabled, Enter ITEM 3 EXEC **(AFT Keypad)** \\ * Set PL BAY DOOR (SYS 1 & SYS 2) To ENABLE \\ * Set PL BAY DOOR To CLOSE \\ * Set PL BAY DOOR To STOP \\ * Set PL BAY DOOR (SYS 1 & SYS 2) To DISABLE \\ * Enter ITEM 2 EXEC **(AFT Keypad)** ​ | Close Payload Bay Doors \\ \\ \\ \\ \\ \\ \\ \\ Wait Until The PL BAY DOOR Talkback Shows CL. |+^  1006  |  Mission Dep.  |  Right Aft  |  R11L \\ \\ \\ \\ R13L \\ \\ \\ \\ R11L  | * If Required, Enter [[ops2#​ops2021|OPS 202 PRO]] **(AFT Keypad)** \\ * Set MAJ FUNC Switch To SM \\ * Enter ITEM 1 EXEC **(AFT Keypad)** \\ * If Not Already Enabled, Enter ITEM 3 EXEC **(AFT Keypad)** \\ * Set PL BAY DOOR (SYS 1 & SYS 2) To ENABLE \\ * Set PL BAY DOOR To CLOSE \\ * Set PL BAY DOOR To STOP \\ * Set PL BAY DOOR (SYS 1 & SYS 2) To DISABLE \\ * Enter ITEM 2 EXEC **(AFT Keypad)** ​ | Close Payload Bay Doors \\ \\ \\ \\ \\ \\ \\ \\ Wait Until The PL BAY DOOR Talkback Shows CL. |
 ^ ^^^^^^ ^ ^^^^^^
-^  1008  |  Mission Dep.  |  Right Aft \\ \\ \\ \\ Overhead Left \\ Right Aft  |  R11L \\ \\ \\ \\ O6 \\ R11L  | * Set MAJ FUNC To GNC \\ * Press GPC/CRT **(AFT Keypad)** \\ * Enter 4 EXEC **(AFT Keypad)** \\ * Enter OPS 201 PRO **(AFT Keypad)** \\ * Set GENERAL PURPOSE COMPUTER - MODE 3 To RUN \\ * Enter OPS 301 PRO **(AFT Keypad)** ​ | Reconfigure GNC’s For Deorbit ​ |+^  1008  |  Mission Dep.  |  Right Aft \\ \\ \\ \\ Overhead Left \\ Right Aft  |  R11L \\ \\ \\ \\ O6 \\ R11L  | * Set MAJ FUNC To GNC \\ * Press GPC/CRT **(AFT Keypad)** \\ * Enter 4 EXEC **(AFT Keypad)** \\ * Enter [[ops2#​ops201|OPS 201 PRO]] **(AFT Keypad)** \\ * Set GENERAL PURPOSE COMPUTER - MODE 3 To RUN \\ * Enter [[ops3#​ops301|OPS 301 PRO]] **(AFT Keypad)** ​ | Reconfigure GNC’s For Deorbit ​ |
 ^ ^^^^^^ ^ ^^^^^^
 ^  1009  |  Mission Dep.  |  Overhead Left  |  O6  | * Set STAR TRACKER DOOR CONTROL (SYS 1 & SYS 2) to CLOSE \\ * Set STAR TRACKER DOOR CONTROL (SYS 1 & SYS 2) to OFF \\ * Set STAR TRACKER POWER (-Y & -Z) to OFF  | Close Star Tracker Doors \\ Wait Until STAR TRACKER DOOR POSITION Talkback Shows CL.  | ^  1009  |  Mission Dep.  |  Overhead Left  |  O6  | * Set STAR TRACKER DOOR CONTROL (SYS 1 & SYS 2) to CLOSE \\ * Set STAR TRACKER DOOR CONTROL (SYS 1 & SYS 2) to OFF \\ * Set STAR TRACKER POWER (-Y & -Z) to OFF  | Close Star Tracker Doors \\ Wait Until STAR TRACKER DOOR POSITION Talkback Shows CL.  |
Line 23: Line 23:
 ^  1012  |  Mission Dep.  |  Right  |  R2  | * Set He ISOLATION A LEFT/​CENTER/​RIGHT To OPEN \\ * Set He ISOLATION B LEFT/​CENTER/​RIGHT To OPEN \\ * Set PNEUMATICS L ENG He XOVR To OPEN \\ * Set PNEUMATICS He ISOL To OPEN \\ * Set LEFT He INTERCONNECT To - IN OPEN \\ * Set CENTER & RIGHT INTERCONNECT To - OUT OPEN  | Main Propulsion System / Helium Release ​ | ^  1012  |  Mission Dep.  |  Right  |  R2  | * Set He ISOLATION A LEFT/​CENTER/​RIGHT To OPEN \\ * Set He ISOLATION B LEFT/​CENTER/​RIGHT To OPEN \\ * Set PNEUMATICS L ENG He XOVR To OPEN \\ * Set PNEUMATICS He ISOL To OPEN \\ * Set LEFT He INTERCONNECT To - IN OPEN \\ * Set CENTER & RIGHT INTERCONNECT To - OUT OPEN  | Main Propulsion System / Helium Release ​ |
 ^ ^^^^^^ ^ ^^^^^^
-^  1013  |  Mission Dep.  |  Right Aft  |  R11L  | * Confirm MAJ FUNC Set To GNC \\ * Enter SPEC 21 PRO **(AFT Keypad)** \\ * Enter ITEM 16 EXEC  | Final IMU Alignment ​ |+^  1013  |  Mission Dep.  |  Right Aft  |  R11L  | * Confirm MAJ FUNC Set To GNC \\ * Enter [[ops2#​spec_21|SPEC 21 PRO]] **(AFT Keypad)** \\ * Enter ITEM 16 EXEC  | Final IMU Alignment ​ |
 ^ ^^^^^^ ^ ^^^^^^
-^  1014  |  Mission Dep.  |  Center \\ Right \\ \\ \\ \\ \\  \\ \\ \\ \\ Center ​ |  C2 \\ R2 \\ \\ \\ \\ \\ \\ \\ \\ \\ C2  | * Enter ITEM 34 EXEC **(Right Keypad)** \\ * Set BOILER N2 SUPPLY (1/2/3) To ON \\ * Set BOILER PWR (1/2/3) To ON \\ * Set APU FUEL TK VLV (1/2/3) To OPEN \\ * Set APU CNTLR PWR (1/2/3) To ON \\ * Confirm APU AUTO SHUT DOWN (1/2/3) Set To INHIBIT \\ * Confirm HYD MAIN PUMP PRESS (1/2/3) Set To LOW \\ * Confirm APU SPEED SELECT Set To NORM \\ * Confirm APU/HYD Ready To Start Talkbacks Are GREY \\ * Confirm GIMBAL CK 34 On CRT 2 Is Complete \\ * Enter OPS 302 PRO **(Right Keypad)** ​ | Perform OMS Gimbal \\ \\ \\ \\ \\ \\ \\ \\ If there'​s an asterisk next to GMBL CK 34 \\ It means the gimbal check is incomplete. \\ You must wait for the asterisk to Disappear. ​ |+^  1014  |  Mission Dep.  |  Center \\ Right \\ \\ \\ \\ \\  \\ \\ \\ \\ Center ​ |  C2 \\ R2 \\ \\ \\ \\ \\ \\ \\ \\ \\ C2  | * Enter ITEM 34 EXEC **(Right Keypad)** \\ * Set BOILER N2 SUPPLY (1/2/3) To ON \\ * Set BOILER PWR (1/2/3) To ON \\ * Set APU FUEL TK VLV (1/2/3) To OPEN \\ * Set APU CNTLR PWR (1/2/3) To ON \\ * Confirm APU AUTO SHUT DOWN (1/2/3) Set To INHIBIT \\ * Confirm HYD MAIN PUMP PRESS (1/2/3) Set To LOW \\ * Confirm APU SPEED SELECT Set To NORM \\ * Confirm APU/HYD Ready To Start Talkbacks Are GREY \\ * Confirm GIMBAL CK 34 On CRT 2 Is Complete \\ * Enter [[ops3#​ops302|OPS 302 PRO]] **(Right Keypad)** ​ | Perform OMS Gimbal \\ \\ \\ \\ \\ \\ \\ \\ If there'​s an asterisk next to GMBL CK 34 \\ It means the gimbal check is incomplete. \\ You must wait for the asterisk to Disappear. ​ |
 ^ ^^^^^^ ^ ^^^^^^
-^  1015  |  Mission Dep.  |  Center ​ |  C2  | * Confirm (CRT 1, CRT 3, CRT 2) Are Set To MAJ FUNC GNC \\ * Enter SPEC 50 PRO **(Left Keypad)** \\ * Enter SPEC 51 PRO **(Right Keypad)** \\ * Enter ITEM 44 EXEC **(Right Keypad)** | Horizontal Situation & Override Displays ​ |+^  1015  |  Mission Dep.  |  Center ​ |  C2  | * Confirm (CRT 1, CRT 3, CRT 2) Are Set To MAJ FUNC GNC \\ * [[ops3#​spec_50|Enter SPEC 50 PRO]] **(Left Keypad)** \\ * Enter [[ops3#​spec_51|SPEC 51 PRO]] **(Right Keypad)** \\ * Enter ITEM 44 EXEC **(Right Keypad)** | Horizontal Situation & Override Displays ​ |
 ^ ^^^^^^ ^ ^^^^^^
 ^  1016  |  Mission Dep.  |  Center \\ Right  |  C2  \\ R2  | * Press RESUME **(Right Keypad)** \\ * Set APU OPERATE - START/RUN For APU 1  |  | ^  1016  |  Mission Dep.  |  Center \\ Right  |  C2  \\ R2  | * Press RESUME **(Right Keypad)** \\ * Set APU OPERATE - START/RUN For APU 1  |  |
Line 35: Line 35:
 ^  1018  |  Mission Dep.  |  Center \\ Overhead Aft  |  C3 \\ O14  \\ O16  | * Set OMS ENG (LEFT & RIGHT) To OFF \\ * Set L OMS ENG VLV To OFF \\ * Set R OMS ENG VLV To OFF  | Deorbit Burn Complete ​ | ^  1018  |  Mission Dep.  |  Center \\ Overhead Aft  |  C3 \\ O14  \\ O16  | * Set OMS ENG (LEFT & RIGHT) To OFF \\ * Set L OMS ENG VLV To OFF \\ * Set R OMS ENG VLV To OFF  | Deorbit Burn Complete ​ |
 ^ ^^^^^^ ^ ^^^^^^
-^  1020  |  Mission Dep.  |  Center \\ Front  |  C2 \\ F6  | * Enter OPS 303 PRO **(Right Keypad)** \\ * Position The Shuttle To The Correct Attitude ​ | __Correct Attitude Hint__ \\ Pitch The Shuttle To 280 Deg  |+^  1020  |  Mission Dep.  |  Center \\ Front  |  C2 \\ F6  | * Enter [[ops3#​ops303|OPS 303 PRO]] **(Right Keypad)** \\ * Position The Shuttle To The Correct Attitude ​ | __Correct Attitude Hint__ \\ Pitch The Shuttle To 280 Deg  |
 ^ ^^^^^^ ^ ^^^^^^
 ^  1022  |  Mission Dep.  |  Center ​ \\  \\ Right  \\ \\ Overhead Aft \\ Right \\ Center ​ |  C2  \\ \\  R2 \\ \\ O17 \\ R1 \\ C2  | * Enter ITEM 36 EXEC **(Right Keypad)** \\ * Enter ITEM 37 EXEC **(Right Keypad)** \\ * Set APU OPERATE - START/RUN For APU (2 & 3) \\ * Set HYD MAIN PUMP PRESS (1/2/3) To NORM \\ * Set ATVC - (1/2/3/4) To ON \\ * Set AC BUS SNSR (1/2/3) To MONITOR \\ * Enter ITEM 39 EXEC **(Right Keypad)** ​ | Dump RCS Propellant \\ \\ Pressure Shuold Rise To 3000 PSI  | ^  1022  |  Mission Dep.  |  Center ​ \\  \\ Right  \\ \\ Overhead Aft \\ Right \\ Center ​ |  C2  \\ \\  R2 \\ \\ O17 \\ R1 \\ C2  | * Enter ITEM 36 EXEC **(Right Keypad)** \\ * Enter ITEM 37 EXEC **(Right Keypad)** \\ * Set APU OPERATE - START/RUN For APU (2 & 3) \\ * Set HYD MAIN PUMP PRESS (1/2/3) To NORM \\ * Set ATVC - (1/2/3/4) To ON \\ * Set AC BUS SNSR (1/2/3) To MONITOR \\ * Enter ITEM 39 EXEC **(Right Keypad)** ​ | Dump RCS Propellant \\ \\ Pressure Shuold Rise To 3000 PSI  |
 ^ ^^^^^^ ^ ^^^^^^
-^  1023  |  Mission Dep.  |  Center \\ \\ Overhead Right \\ \\ \\ Center ​ |  C2 \\ \\  O8  \\  \\  \\ C2  | * Enter ITEM 38 EXEC **(Right Keypad)** \\ * Enter ITEM 40 EXEC **(Right Keypad)** \\ * Set FWD RCS - He PRESS (A & B) To CLOSE \\ * Set TANK ISOLATION (1/2 & 3/4/5) To CLOSE \\ * Set MANIFOLD ISOLATION (1/2/3/4/5) To CLOSE \\ * Enter OPS 304 PRO **(Right Keypad)** ​ | Wait Until The cycle Completes ​ |+^  1023  |  Mission Dep.  |  Center \\ \\ Overhead Right \\ \\ \\ Center ​ |  C2 \\ \\  O8  \\  \\  \\ C2  | * Enter ITEM 38 EXEC **(Right Keypad)** \\ * Enter ITEM 40 EXEC **(Right Keypad)** \\ * Set FWD RCS - He PRESS (A & B) To CLOSE \\ * Set TANK ISOLATION (1/2 & 3/4/5) To CLOSE \\ * Set MANIFOLD ISOLATION (1/2/3/4/5) To CLOSE \\ * Enter [[ops3#​ops304|OPS 304 PRO]] **(Right Keypad)** ​ | Wait Until The cycle Completes ​ |
 ^ ^^^^^^ ^ ^^^^^^
 ^  1024  |  Mission Dep.  |  Front Left \\ Front Right  |  F6  \\  F8  | * Set Commander ATTITUDE INRTL To LVLH  \\ * Set Pilot ATTITUDE INRTL To LVLH  |  | ^  1024  |  Mission Dep.  |  Front Left \\ Front Right  |  F6  \\  F8  | * Set Commander ATTITUDE INRTL To LVLH  \\ * Set Pilot ATTITUDE INRTL To LVLH  |  |
deorb-checklist.txt · Last modified: 2008/11/12 07:03 by uri_ba