User Tools

Site Tools


ops2

This is an old revision of the document!


OPS2

The CRTs have three Modes GPC, SM and PL - every program has different displays for each mode. The two Main modes in SSM2007 are GPC, used for on orbit manuvering and system settings and SM used for Mission Payload OPS.

CRT Control Switches
CRT2 Contol switches

All four CRTs allow the crew the same functions. the three forward CRTs are controlled from the C2 Panel while the Rear CRT is controlled from the R11 Panel.

FIXME

GPC Mode

OPS201

OPS201 Screen - GPC Mode

UNIV PTG

MNVR OPTIONS
  • ITEM 5, 6 & 7 - target attitude values for auto maneuvering

OPS202

OPS202 screen - GPC Mode

ORBIT MNVR EXEC

Burn information box
  • Burn Countdown timer - Under the MET on the top right corner of the screen is the Countdown timer for the burn (activated by ITEM 23).
  • ΔVTOT - The Delta (difference) between current and required Orbital velocity in Feet\Sec.
  • TGO - Time Remaining in the burn.
  • VGO - Displays difference between the current orbit and the target orbit on each of the plane.
  • Orbit Information - Shows Apogee and perigee heights (HA and HP) for current and target orbits in NM.
OMS burn Mode

allows the crew to set which type of burn will be performed.

  • ITEM 1 - Select Both OMS engines for a burn
  • ITEM 2 - Select Left OMS engine only for a burn
  • ITEM 3 - Select Right OMS engine only for a burn
  • ITEM 4 - Select RCS thrusters for a burn (do not fire OMS engines)
Burn Trim

for “dialing” in the required Trim for the upcoming burn - once modified Load must be performed for the new Data to be accepted.

  • ITEM 5 -
  • ITEM 6, 7 & 8 -
  • ITEM 9 - Shuttle's weight - updates automatically, but can also be manually updated by the Crew or by uplink from GC
  • ITEM 10 -
Burn Targets
  • ITEM 14, 15, 16 & 17 -
  • ITEM 18 -
  • ITEM 19, 20 & 21 - ΔV values for the burn on each axis (ft/sec).
  • ITEM 22 - Load Burn Targets
  • ITEM 23 - Initiat Burn CountDown
BURN ATT

The Required Attitude for the upcoming burn - this section also allows the crew to change the attitude and order the Shuttle to maneuver itself to the programed attitude.

  • ITEM 24, 25 & 26 -
  • ITEM 27 - Start Auto Manuver to Programed Attitude
REI

displays the Time to apogee (TTA) or the Time To perigee (TTP)

GMBL

Displays and controls the gimbals of the OMS engines (left & right).

  • ITEM 28 & 29 - Select Primary OMS Gimbals
  • ITEM 30 & 31 - Select Secondary OMS Gimbals
  • ITEM 32 & 33 - Turn Off OMS Gimbals.
  • ITEM 34 - Check OMS Gimbals movement.
Abort
  • ITEM 35 - Abort (Unload) Burn Target
FWD RCS
  • ITEM 36 - Arm Forward RCS fuel Dump
  • ITEM 37 - Dump Forward RCS fuel
  • ITEM 38 - Stop Forward RCS fuel Dump
SURF DRIVE
  • ITEM 39 - Initiate Hydraulic surfaces self test sequence
  • ITEM 40 - Terminate Test-sequance once it is over.

SPEC 00

SPEC 01

SPEC 02

SPEC 06

SPEC 19

SPEC 20

SPEC 21

IMU

SPEC 22

SPEC22

Star Traker

  • ITEM 1&2 - Self Test
  • ITEM 3&4 - Star Track
  • ITEM 5&6 - Target Track
  • ITEM 7&8 - Stop Track
  • ITEM 9&10 - Terminate track/System IDLE
  • ITEM 11&12 - Select targets
  • ITEM 13&14 -
  • ITEM 15&16 -

COAS - Not implemented in SSM2007

  • ITEM 17, 18 & 19 - Not implemented in SSM2007
  • ITEM 20 - Not implemented in SSM2007
  • ITEM 21 - Not implemented in SSM2007
  • ITEM 22 - Not implemented in SSM2007
  • ITEM 23 - Not implemented in SSM2007
  • ITEM 24 - Not implemented in SSM2007
  • ITEM 25 - Not implemented in SSM2007
  • ITEM 26&27 - Not implemented in SSM2007
  • ITEM 28&29 - Not implemented in SSM2007

SPEC 25

SPEC 33

SPEC33

KU Band

  • ITEM 1 - Rendezvous Mode
  • ITEM 2 - KU-Band antenna (Enable/Disable)
  • ITEM 3 -

SPEC 34

SPEC 55

SPEC 99

Error Display - No Options

SM Mode

FIXME

OPS201

OPS201 Screen - SM Mode

OPS202

OPS202 Screen - SM Mode

Payload Bay Doors

  • ITEM 1 - Door AC power ON
  • ITEM 2 - Door AC power OFF
  • ITEM 3 - Door Auto mode (enable/disable)
  • ITEM 4, 5, 6 & 7 -
  • ITEM 8, 9 & 10 -
  • ITEM 11, 12 & 13 -
  • ITEM 14 -
  • ITEM 15 -
  • ITEM 16 -
  • ITEM 17 -

SPEC 0

SPEC 1

SPEC 2

SPEC 94

PDRS Control

  • ITEM 1 - Not implemented in SSM2007
  • ITEM 2 - Not implemented in SSM2007
  • ITEM 3 - Not implemented in SSM2007
  • ITEM 4 - Not implemented in SSM2007
  • ITEM 5 - Not implemented in SSM2007
  • ITEM 6 - Not implemented in SSM2007
  • ITEM 7 - Enable RMS Soft Stop (Default)
  • ITEM 8 - Disable RMS Soft Stop
  • ITEM 9 -
  • ITEM 10 -
  • ITEM 11 -
  • ITEM 12 -
  • ITEM 13, 14, 15 & 16 - Not implemented in SSM2007
  • ITEM 17 - Not implemented in SSM2007
  • ITEM 18, 19 & 20 - Not implemented in SSM2007
  • ITEM 21, 22 & 23 - Not implemented in SSM2007
  • ITEM 24 - Not implemented in SSM2007
  • ITEM 25 - Not implemented in SSM2007
  • ITEM 26 -
  • ITEM 27 -
  • ITEM 28 -
  • ITEM 29 -
  • ITEM 30 - Not implemented in SSM2007
  • ITEM 31, 32 & 33 - Not implemented in SSM2007

SPEC 96

Spec 96

PDRS Faults

ops2.1256021595.txt.gz · Last modified: 2009/10/20 06:53 by uri_ba